Features:Easy to install, manual control, high reliability, mechanical limit, the output signal
1.
Intriduction:
The damper drive is mainly used in HVAC dampers automatic control
Feature:
●Easy Installation:Fixed on the damper shaft through a universal shaft holder
● Hand Control:Manual operation is possible via pushbuttons when is required
●High reliability: The driver has the overload protection function
● Mechanical limit: Built-in mechanical limit can be adjusted mechanical limit.
● Output single:In the 0-100% range can output a switch signal.
● –The DS type includes a set of auxiliary switches
Main Technical Data:
扭矩 |
2Nm |
seveice life |
Rotate 10,000 times |
Panel area |
0.5㎡ |
Operating time |
30S(90°) |
Voltage |
AC/DC 24V |
Rate |
50/60HZ |
Control single |
2or3 |
turn direction |
manufacture control |
Manufacture control |
qulified |
turn angle |
0- 90° |
direction |
Machcian control |
power |
2W |
Noise |
45dB |
Protect class |
Ⅱ |
Protect class |
IP54 |
ambinet tempreture |
-20~+50℃ |
ambinet humidify |
5-95%RH |
length |
﹥50㎜ |
size |
6-16㎜ / 12×12 |
weight |
﹤0.5Kg |
Standard |
CE |
2.Analog (adjustable) damper actuators
Introduction:
The damper drive is mainly used in HVAC dampers automatic control.
Feature:
●Easy Installation:Fixed on the damper shaft through a universal shaft holder
● Hand Control:Manual operation is possible via pushbuttons when is required
●High reliability: The driver has the overload protection function
● Mechanical limit: Built-in mechanical limit can be adjusted mechanical limit.
● Output single:In the 0-100% range can output a switch signal.
● –The DS type includes a set of auxiliary switches。
Technical data:
扭矩 |
2Nm |
sevice life |
turn100,000time |
panel area |
0.5㎡ |
operating time |
30S(90°) |
voltage |
AC/DC 24V |
power |
50/60HZ |
control single |
0(2)…10V / 0(4)…20mA |
turn direction |
manufacturer control |
manufacture machine |
qualified |
turn angle |
0- 90° |
position |
adjust machine |
power |
2W |
noise |
45dB |
protact class |
Ⅱ |
protact grad |
IP54 |
3.water valve
1.Switch - type water valve
Feature:
●The tightening force of the driver LA18MU220-D is 1800N.
● action using gear transmission, the center of the gear rotation around the central axis of the roller.
● Straight travel indicator.
● When the drive reaches the limit position, the circuit will delay for a certain period of time to ensure that the valve opens and closes.
Technical data:
Model |
LA18MU220-D |
Torque |
1800N |
operating type |
Reversible |
control tyoe |
Floating point control |
output signal |
no |
Feedback signal |
no |
voltage |
220VAC 50/60Hz 13.5W |
Maximum length |
42㎜ |
Conductor specifications |
0.75㎡ |
25 mm running time |
138S |
Noise |
40dB |
Adapt to the valve caliber |
DN50-DN125 |
working tempreture |
-20…+50℃ |
Protact grad |
IP42 |
weight |
4Kg |
Attention:
● The drive must be protected against water leakage and damage to internal parts and motors.
● The driver can not be covered by the insulation material, so as to avoid burning the motor due to poor heat dissipation.
● When servicing the drive, the power must be disconnected to prevent damage to the device or to cause electric shock.
● Do not touch or attempt to remove wires while the power is connected.
2.Analog type (regulated type) water valve
Feature:
● The closing force of the driver LA18MU24-A is 1800N.
● action using gear transmission, the center of the gear rotation around the central axis of the roller.
● Straight travel indicator.
●Circuit in the drive reaches the limit position, will produce a period of time delay to ensure that the valve opens and shuts off。
Technical Data:
Model |
LA18MU24-A |
Torque |
1800N |
Mode of operation |
Reversible |
Control type |
Proportional control (intelligent adjustment type) |
Input Signal |
0(2)-10V , 0(4)-20mA |
Feedback signal |
0(2)-10V |
Electrical rating of the motor |
24VAC 50/60Hz 13.5W |
Max.length |
42㎜ |
Conductor specifications |
0.75㎡ |
25㎜operating time |
166S |
Noise |
40dB |
Adapt to the valve caliber |
DN50-DN125 |
working tempreture |
-20…+50℃ |
Protact grad |
IP42 |
weight |
4Kg |
Attention:
● The drive must be protected against water leakage and damage to internal parts and motors.
● The driver can not be covered by the insulation material, so as to avoid burning the motor due to poor heat dissipation.
● When servicing the drive, the power must be disconnected to prevent damage to the device or to cause electric shock.
● Do not touch or attempt to remove wires while the power is connected.